<

Foggy windows? Signs Your Window Seals Have Failed

Serving Pleasanton, Dublin, Livermore, San Ramon, Danville, and Walnut Creek since 1997

If you have noticed a hazy film or small water droplets trapped between the panes of a dual-pane window, and it won't wipe away from either side, the seal around that glass has most likely failed. It isn't an emergency, and it doesn't always mean the whole window needs replacing. But it does mean the window has lost some of its insulating ability, and the problem won't fix itself.

The first cold mornings of a Bay Area fall are often when homeowners notice it for the first time. Moisture that crept into the glass over a long, hot summer finally condenses when nighttime temperatures drop. This guide walks through how to confirm a failed seal, why it happens, what your repair and replacement options are, and how to decide which one makes sense for your home.

‍

What a window seal actually is

Most windows installed in the last few decades use an insulated glass unit, often shortened to IGU. It is two (or sometimes three) panes of glass separated by a spacer around the edges. The space between the panes is filled with dry air or an insulating gas such as argon, and the edges are sealed at the factory to keep outside air and moisture out.

Inside the spacer is a desiccant, a drying material that absorbs any small amount of moisture that gets in. As long as the seal holds, the desiccant keeps up and the glass stays clear. When the seal breaks down, humid outside air slowly works its way in, the desiccant eventually becomes saturated, and moisture begins condensing on the inside surfaces of the glass.

This is different from the weatherstripping and caulk around the window frame. Those can be maintained or replaced. The seal on the glass unit cannot be repaired in place.

‍First, make sure it's actually seal failure

Not every foggy window has a failed seal. Condensation can show up in three different places, and only one of them points to a seal problem.

➔ On the inside surface (the side facing your room): This is an indoor humidity issue, not a seal failure. It's common in bathrooms, kitchens, and bedrooms on cold mornings. Better ventilation or a dehumidifier usually helps.

➔ On the outside surface: Moisture on the exterior glass on a cool, humid morning is generally harmless. It is actually more common with energy-efficient glass, because less of your home's heat is escaping through the window to warm the outer pane.

➔ Between the panes: If you can't wipe it away from either side, the moisture is inside the sealed unit. That is seal failure.
‍

The simple test: wipe the glass on both sides with a dry cloth. If the haze is still there, it's between the panes.

‍

Signs your window seals have failed

Seal failure tends to build gradually. Look for these signs, ideally once on a sunny afternoon and again on a cool morning:

➔ Fog or haze between the panes that can't be wiped from either side

➔ Fogging that comes and goes with the sun or the time of day, which often happens early on, before the problem becomes permanent

➔ Water droplets between the panes, often collecting along the bottom edge

➔ A white, milky film or streaks that stay even when the window is dry, a sign that moisture has been cycling inside the unit for a while and has left mineral deposits on the glass

➔ The same problem on several windows, especially on the same side of the house

One clarification: a failed glass seal doesn't usually cause a draft. If you feel air moving around a window, the more likely cause is worn weatherstripping, a sash that no longer closes tightly, or a gap where the frame meets the wall. That's a separate problem, but it often shows up on the same aging windows, and it's worth checking for both at once.

‍

Why window seals fail

Seal failure is mostly a result of age and temperature. As the sun heats a window during the day and the glass cools at night, the air or gas between the panes expands and contracts. Over thousands of these cycles, that constant movement weakens the edge seal until it cracks or loses adhesion and lets moist air in.

Several factors speed the process up:

➔ Large daily temperature swings. The bigger the gap between daytime and nighttime temperatures, the more the seal is stressed each day.

➔ Direct sun exposure. South- and west-facing windows heat up the most and tend to show seal problems first.

➔ Frame movement. Window frames expand and contract with temperature too. A frame that moves much more than the glass it holds puts added stress on the seal.

➔ Manufacturing quality. Poorly applied sealant or an undersized desiccant load can cause a seal to fail early.

➔ Age. Even well-made seals eventually wear out. If your windows are 20 or more years old, some seal failure is expected.

‍

Why Tri-Valley and inland East Bay windows take a harder hit

Inland Bay Area communities put windows through more temperature cycling than many homeowners realize. In Livermore, July averages a high of about 87°F and a low of about 58°F, a swing of roughly 30 degrees every summer day. Pleasanton, Dublin, San Ramon, and Danville see a similar pattern: hot, sunny afternoons followed by cool nights once the marine air moves through the valleys.

That means a sun-facing window in the Tri-Valley may go through a significant expansion and contraction cycle nearly every day from late spring through early fall. Homes closer to the bay, in places like Fremont, Alameda, and Berkeley, see milder swings but more humidity, so a seal that does fail tends to let in more moisture.

The result is the same in both cases. Seals that might last longer in a milder climate are under steady pressure here, and fall is when the damage tends to become visible.

‍

Does a failed seal really matter?

In the short term, the biggest issue is how it looks. A fogged window is hard to see through, and over time the moisture can leave permanent mineral etching on the glass that cleaning won't remove.

There is also a performance cost. When the seal fails, the insulating gas between the panes leaks out and is replaced by ordinary humid air, so the window loses part of the insulating advantage it was designed to provide. A single fogged window isn't going to change your energy bill noticeably, but several failing windows on a sun-exposed wall can make a room harder to keep comfortable in summer and winter.

None of this is urgent. But the fogging will get worse, not better, so it's worth planning your next step.

‍

Your options for a failed window seal

There are three common approaches, and the right one depends on how many windows are affected and what condition the frames are in.

1. Defogging services

Some companies drill small holes in the glass, clean and dry the space between the panes, and then reseal the holes. This can improve the appearance, but it doesn't restore the original gas fill or the factory seal, results vary, and fogging can return. It's best thought of as a cosmetic, temporary fix.

2. Replacing just the glass unit

A glass professional removes the failed insulated glass unit and installs a new one in the existing frame. This restores a clear view and a fresh seal without replacing the whole window. It can be a sensible choice when only one or two windows are affected, the frames are in good condition, and the windows are otherwise performing well.

Before paying for any repair, check your window paperwork. Many manufacturers warranty the glass seal for a set period, so a newer window with a failed seal may be covered.

3. Replacing the whole window

Full replacement makes more sense when:

➔ Several windows are fogging, especially on the same wall. If one has failed, others of the same age and exposure are likely on the same timeline.

➔ The frames themselves are showing problems, such as warping, sashes that stick or won't lock, or gaps you can feel.

➔ The windows are older aluminum or vinyl units that were never very energy efficient to begin with.

➔ You're already feeling drafts, hearing more outside noise, or struggling to keep certain rooms comfortable.

In these situations, replacing individual glass units means paying to repair windows that are near the end of their useful life anyway. A full replacement addresses the seal, the frame, and the overall energy performance at the same time.

‍

How frame material affects how long seals last

When you do replace windows, the frame material plays a bigger role in seal life than most homeowners expect. Glass barely changes size as it heats and cools. A frame that expands and contracts much more than the glass pulls and pushes on the seal every day.

According to Marvin's published materials testing, vinyl expands and contracts at more than six times the rate of glass. Infinity by Marvin fiberglass windows are made from Ultrex, a pultruded fiberglass that expands and contracts at nearly the same rate as glass. Because the frame and the glass move together, there is less day-to-day stress on the seal, and the window stays tighter through repeated temperature swings.

For Tri-Valley homes that see hot afternoons and cool nights for months at a time, that stability is a practical advantage, not just a spec sheet number. It's also one of the main reasons fiberglass windows cost more than vinyl up front.

Installation matters too. A window that is installed out of square or without proper support puts uneven pressure on the frame and the glass. That is why Custom Exteriors uses AAMA Certified Master Installers who are full-time employees, not subcontractors.

‍

What to do if you've spotted fogged windows

➔ Confirm it's between the panes. Wipe both sides of the glass on a cool morning.

➔ Walk the whole house. Note which windows are affected and which direction they face. A pattern on one side of the house tells you a lot.

➔ Check for other problems at the same time. Look for drafts, sticking sashes, and damaged frames.

➔ Find your warranty paperwork. Newer windows may still be covered for seal failure.

➔ Get a professional opinion. An in-home consultation can help you decide whether glass replacement, full window replacement, or simply waiting makes the most sense for your home and budget.

‍

Why East Bay homeowners work with Custom Exteriors

Custom Exteriors has served Bay Area homeowners since 1997 and has completed more than 30,000 projects. Our installers are AAMA (American Architectural Manufacturers Association) Certified Master Installers and full-time Custom Exteriors employees. We are a Diamond Certified company with more than 200 five-star reviews.

If you're seeing fogged windows, we'll give you a straight answer about whether they need to be replaced. Not every fogged window does, and we'll tell you when a simpler fix makes more sense. When replacement is the right call, our Pleasanton showroom lets you see and operate Infinity by Marvin windows in person before you decide.

‍

Frequently asked questions

Can a failed window seal be repaired?  The original factory seal can't be repaired in place. Defogging services can improve the appearance temporarily, but they don't restore the original gas fill. The lasting fixes are replacing the glass unit or replacing the whole window.

Is condensation on the inside of my windows a sign of seal failure?  No. Condensation on the room-side surface that you can wipe away is caused by indoor humidity. Seal failure only shows up as moisture between the two panes of glass.

Will a failed window seal raise my energy bill?  A single failed seal usually has a small effect. The window loses some insulating value because the gas between the panes has leaked out, but the bigger energy impact comes when several windows are failing, or when the frames are also leaking air.

How long should window seals last?  It depends on the quality of the glass unit, the frame material, sun exposure, and the local climate. Seals on sun-facing windows in hot inland areas like the Tri-Valley tend to fail sooner than seals on shaded windows or in milder coastal climates. If your windows are more than 20 years old and starting to fog, it's a good time to evaluate all of them, not just the ones you can see are failing.

Do I need to replace all my windows if only one has a failed seal?  Not necessarily. If one newer window has failed and the rest are in good condition, replacing that single glass unit, or making a warranty claim, may be all you need. If several windows of the same age are fogging, the others are likely to follow, and a planned replacement is often more cost-effective than repairing them one at a time.

Seeing fog between your window panes? Schedule a consultation for an honest assessment of your windows, or visit our Pleasanton showroom to see Infinity by Marvin fiberglass. 

‍

2142 Rheem Drive, Suite E, Pleasanton, CA  |  (866) 568-4314  |  custom-exteriors.com

Est. 1997  |  30,000+ projects  |  Diamond Certified  |  AAMA Certified Master Installers  |  Infinity from Marvin Platinum Partner